Innokin ZENITH Replacement Coil x 5
Description
Innokin Zenith Coil Heads (5 pcs)
Innokin Zenith coils 1.6ohm (10 to 14 watts) / 1.2ohm (14 tot 18watts) for use in the Innokin Zenith tank. The coils have been specially developed for Mouth To Long (MTL) vapers and offer a pure taste. The coils are extremely suitable for e-liquids with a maximum VG value of 60%. Best used at wattages from about 10 to 14 watts
Innokin Zenith coils 0.8ohm for use in the Innokin Zenith tank. The coils have been specially developed for MTL and DTL vapers and offer a pure taste. The coils are extremely suitable for e-liquids with a maximum VG value of 60%. Best used at wattages from about 15 to 18 watts
Innokin Zenith Plexus coils 0.5ohm for use in the Innokin Zenith tank. The coils have been specially developed for DTL vapers and offer a pure taste. The coils are extremely suitable for e-liquids with a maximum VG value of 60%. Best used at wattages from about 14 to 19 watts
NOTE: Always let the e-liquid draw well into the coil before using the e-cigarette, if using a new coil, let it stand for 5 minutes before using it. Fill the tank on time and do not empty it completely to prevent combustion of the coil.
Product content:
- These coils are sold per box of 5 pieces.
Specifications
- Brand: Innokin
- Model: Zenith
- Suitable for: Zenith clearomizer
- Packaging: 5 pieces
- Material: Japanese cotton
HOW TO REPLACE THE ZENITH COIL?
- Open the reservoir of the Zenith vaporizer to shut off the flow of e-liquid to the resistor.
- Hold the vaporizer upright
- Unscrew the lower part, called Bottom Cap
- Remove the resistance
- Insert a new resistor Zenith
- Screw the bottom cap of the vaporizer back on
- Ignite the resistance
FILLING THE COIL
- Filling consists of pouring enough e-liquid into a new one. Here are some tips for an optimal refill:
- Close the Airflow ring as much as possible so that as little air as possible flows into it.
- Without turning on the battery, you inhale in 3 vacuums to let the e-liquid run into the coil.
- Wait 3 minutes before using your e-cigarette.
WARNING SIGN
Your battery must be compatible with the value of the Zenith resistor you will be using. For use with, for example, resistances Zenith 0.8 Ohm, your box must be able to withstand resistances of at least 0.8 Ohm.
Important before first use:
Always moisten a coil before first use to prevent burning and let it soak in for a while. If the coil is used too dry, a burnt taste will develop. Moisten a coil by dropping a few drops of liquid on all visible and/or invisible cotton wool/cotton/wick so that it absorbs well with liquid. If possible, moisten the center of the coil as well. Usually a coil liquid flow has holes all around. Also moisten these holes with a drop of liquid. To be extra sure that a coil is well soaked with liquid, you can take a few pulls without activating the battery. Humidification of a coil is only necessary when using a new coil for the first time.
If a coil contains too much liquid and starts to bubble and/or splash:
Remove the coil and blow it out from top to bottom over a tissue. In this way you blow the excess liquid out of the coil. Then place the coil back and always tighten it firmly.
Set Wattage/Voltage:
Most coils have the Wattage/Voltage engraved on which they can be used. Always start with the lowest indicated wattage on the coil (after moistening) and adjust it if desired to the highest indicated wattage at the latest (note: the highest indicated wattage is not necessarily necessary for a good vapor/taste experience!). Always check first whether your equipment can handle the indicated wattage.