Vaporesso GTX Mesh Heads (5 pieces per pack)

The GTX Coils are made by the manufacturer Vaporesso and are supplied per pack of 5 pieces. The coils can be replaced from the bottom of the pod by pulling the old one out and pressing the new one in. This makes these coils easy to install in the vape pod. In addition, these coils are available for both MTL and DL use. That is why there is the right coil for every vaping style.

The resistances (ohms)

The Vaporesso GTX Coils are available in different resistances. As a result, each type of coil has its own effect.

• 0.2 ohm Mesh coil

The 0.2 ohm mesh coil for the Vaporesso PM80 has a resistance of less than 0.5 ohms. Therefore, the 0.2 ohm coil is suitable for direct lung use. With this coil you can inhale like a water pipe. The filament of this coil has a mesh structure made for full flavor and a lot of vapor. The recommended setting for this coil is between 45 and 60 Watts. We recommend at least 70% VG e-liquid for this coil.

• 0.3 ohm Mesh coil

The 0.3 ohm Mesh coil has a resistance of below 0.5 ohm just like the 0.2 ohm. Therefore, the 0.3 ohm coil is very suitable for direct lung (DL) use. Because this coil has a higher ohm than the 0.2 ohm variant, it gives slightly less flavor and vapor but is more economical with e-liquid and the battery. This coil is made for intense flavor with full vapor and works best between 32 and 45 watts. We recommend at least 70% VG e-liquid for this coil.

• 0.6 ohm mesh

The 0.6 ohm GTX coil has a resistance of less than 1 ohm. Therefore, the 0.6 ohm coil is suitable for direct lung or strong mouth to lung use. With this coil you can inhale like a water pipe or like a cigarette. The filament of this coil has a mesh structure made for full flavor and a lot of vapor. The recommended setting for this coil is 20-30W. Thanks to the mesh filament, the 0.6 ohm GTX Mesh coil gives more flavor and vapor than regular coils. We recommend at least 50% VG e-liquid for this coil.

• 0.8 ohm MTL Mesh

The 0.8 ohm MTL Mesh coil has a resistance of less than 1 ohm. Therefore, the 0.8 ohm coil gives a strong mouth to lung experience. With this coil you can inhale like a cigarette. The filament of this coil has a mesh structure made for full flavor and a lot of vapor. The recommended setting for this coil is 12-20w. This coil is a lot stronger than the 1.2 ohm variant. We recommend at least 50% VG e-liquid for this coil.

• 1.2 ohms Regular

The 1.2 ohm regular GTX coil has a resistance of above 1 ohm. That is why the 1.2 ohm coil is very suitable for mouth to lung (MTL) use. MTL is a way of inhaling that is comparable to the traditional cigarette. This coil is made for high nicotine strength e-liquids and works best from 8 to 12w. We recommend a maximum of 50% VG e-liquid for this coil.
Where do the Vaporesso GTX Coils fit?

Almost every vape model uses different coils. The Vaporesso GTX Coils are suitable for the following products:

• Vaporesso PM80 pod set
• GTX One kit
• Target PM80 SE vape

Tips for use

Before you can start using the coil, it will have to withdraw with e-liquid. You can do this by putting a few drops of e-liquid in the coil before it is installed and letting it soak in briefly. Another option is to install the coil and let it sit for 10 minutes so that it can fill with e-liquid. The coil is then ready for use. We recommend that you always use the correct ratio of e-liquid and use the recommended settings. As a result, your coil will last longer and you will experience a nicer effect. The recommended settings are indicated in the above description and on the coil itself. The Vaporesso GTX coil lasts on average 1 to 2 weeks. This of course depends on usage. If the coil tastes burnt, it also needs to be replaced. Therefore, make sure that there is always enough e-liquid in the tank, so that the coil does not burn through

Contents

5x Vaporesso GTX Coils

• Brand Vaporesso
• Filling material Organic Cotton
• Rebuildable (RBA) No
• Way of inhaling Direct Lung
• Warranty DOA